Bookmarks
Archive
-
▼
2012
(42)
-
▼
April
(42)
- Diode Tutorial
- Cathode Ray Tube (CRT) Tutorial
- Circuit Components Symbols Tutorial
- Capacitors Tutorial
- Batteries Tutorial
- Active and Passive Tutorial
- 7 Segment Display Tutorial
- Time Constants Tutorial
- What is Phase Tutorial
- The RF Spectrum Tutorial
- The Integrator Tutorial
- The Differentiator Tutorial
- Source and Load Tutorial
- Sound Tutorial
- Semiconductor Materials
- RMS and Peak to Peak Tutorial
- Pulses Tutorial
- Pulse Modulation Tutorial
- Percent and Tolerance Tutorial
- Oscillators Tutorial
- Ohms & Kirchhoff's Law Tutorial
- Motor Principle
- Mixer Tutorial
- Magnetism Tutorial
- Light Tutorial
- Heat Tutorial
- Harmonics Tutorial
- Graphs and Waveforms Tutorial
- Generator Principle Tutorial
- Frequency Modulation (FM) Tutorial
- Frequency Changer Tutorial
- Filters Tutorial
- Feedback Tutorial
- Electromagnetism Tutorial
- Difference Amplifier
- Conductors and Insulators Tutorial
- Clippers and Limiters Tutorial
- Circuit Symbols Tutorial
- Circuit Diagrams Tutorial
- Circuit diagrams
- Amplitude modulation
- Amplifiers tutorial
-
▼
April
(42)
Popular Posts
-
The generator at the power station which produces our AC mains rotates through 360 degrees to produce one cycle of the sine wave form whic...
-
It is best if you read the page on THE MIXER first. There are many thousands of radio stations in the world, transmitting on thousands ...
-
If someone measures the value of the AC voltage coming out of a transformer using an oscilloscope and says it is 20 volts peak to peak an...
-
Like charges repel, unlike attract. In the first diagram, when the switch is closed, the negative terminal of the battery repels the neg...
-
Circuit diagrams are one method of describing electronic equipment. They are made up of BS3939 standard circuit symbols. READING a ci...
-
Read the page on TIME CONSTANTS before trying this one. The differentiator is made from a capacitor C, and resistor R, and assembled a...
-
It is best if you read the page on the PHASE first. Feedback is when some of the output signal from a circuit is fed back to the input an...
-
When current travels through a wire, a magnetic field, made of lines of force, is formed around the wire. If the wire is coiled, the lines...
-
It is best if you read the page on the Magnetism first. When a piece of wire is moved through a magnetic field, a voltage and current is ...
-
A filter circuit is like a sieve. It allows some things through and holds back others. In this case we are talking about AC frequencies. ...
About Me
- omkar singh infifnity
- राष्ट्रवादी सोच तकनिकी ज्ञान अध्यात्मिक ज्ञान वसुधैव कुटुम्बकम विचारधारा
Blogroll
Saturday, 21 April 2012
Amplitude modulation
Published :
09:01
Author :
omkar singh infifnity
If you connect a long wire to the output terminals of your Hi-Fi amplifier and another long wire to the input of another amplifier, you can transmit music over a short distance. DON'T try this. You could blow up your amplifier.
A radio wave can be transmitted long distances. To get our audio signal to travel long distances we piggyback it onto a radio wave. This process is called MODULATION.
The radio wave is called the CARRIER.
The audio signal is called the MODULATION.
At the receiving end the audio is recovered by a process called DEMODULATION.
From the diagram below, it can be seen that when the carrier is modulated, its amplitude goes above and below its unmodulated amplitude.
It is about 50% modulated in the diagram. The maximum percentage modulation possible is 100%. Going above this causes distortion.
Most broadcasters limit modulation to 80%.
Modulating the carrier frequency with an audio frequency produces two new frequencies. At this point it would be a good idea to read the page on MIXERS. These new frequencies are called the upper and lower SIDEBANDS. The upper sideband is the carrier frequency plus the audio frequency. The lower side band is the carrier frequency minus the audio frequency.
Since the audio signal is not a single frequency but a range of signals (usually 20 Hz to 20 KHz) the sidebands are each 20Hz to 20 KHz wide.
If you tune across a station in the Medium Wave Band you will find that it takes up space in the band. This is called the signal BANDWIDTH. This is the space taken by the upper and lower sidebands. In the the example given above it would be 40 KHz.
Since the Medium Wave is only 500 KHZ wide there would only be space for about 12 stations.
Therefore the bandwidth of stations is limited to 9 KHz, which limits the audio quality.
If there are two stations too close together, their sidebands mix and produce HETERODYNE whistles.
Since both sidebands carry the same information, one side can be removed to save bandwidth.
This is SSB, single sideband transmission.
Subscribe to:
Post Comments (Atom)
0 comments:
Post a Comment